Hash-Hut 마이닝 풀: Antminer L9 및 L11 설정 가이드

Hash-Hut mining pool is a new BT-Miners partner for customers exploring Litecoin and Dogecoin merged mining. This guide brings the pool introduction and Antminer L9/L11 connection steps together, with the settings to check before moving a machine onto a new endpoint.

Hash-Hut now lists BT-Miners on its Litecoin and Dogecoin pages as a partner Scrypt ASIC seller. We are including Hash-Hut as a pool option to consider alongside your hardware purchase. This partnership introduction is not a claim that we have independently benchmarked pool uptime or earnings.

Why consider Hash-Hut for Litecoin and Dogecoin?

시작하기 Hash-Hut Litecoin mining page Hash-Hut Dogecoin mining page. These are the partner links for current coin information and connection instructions. The pool supports LTC/DOGE merged mining: compatible Scrypt work can contribute to a primary chain and supported auxiliary chains, rather than requiring a second ASIC just for DOGE.

The practical appeal is a single mining connection with account-based monitoring. However, a shared connection does not mean a shared payout wallet. Configure the correct receiving address for each coin you intend to collect. Also review the selected primary coin or switching mode; a Scrypt endpoint alone does not guarantee that the primary route will remain Litecoin.

Choose the correct L9 or L11 specification

Both families use Scrypt. Match the exact unit, power requirements and operating environment before comparing pool estimates. Browse the BT-Miners Litecoin and Dogecoin miner collection for current models and batches.

Daily energy is calculated as rated watts divided by 1,000, multiplied by 24 hours. At an illustrative electricity rate of $0.10/kWh, these configurations use about $8.57 and $8.83 of electricity per day, respectively, before ventilation, cooling and other overhead. These are cost examples, not earnings forecasts.

Do not mix specifications across variants. The L9 also has other performance configurations, while the L11 Pro is a separate model. Check the nameplate and order specification instead of copying a calculator preset. For the basic hardware workflow, see our Antminer L9 setup guide.

Hash-Hut mining pool setup for L9 and L11

1. Prepare the account and payout wallets

Create your Hash-Hut account and locate the stratum ID assigned to it. Add an LTC payout address and a DOGE payout address in the account settings. Copy addresses carefully and verify the intended coin network. Keep a record of the existing miner settings before changing pools so that you can restore a known working configuration.

2. Enter the Scrypt connection settings

Open the miner control panel on your local network and find the pool configuration section. Hash-Hut publishes these regional Scrypt endpoints in the coin-page connection instructions, checked on October 30, 2026:

작업자 형식: USER_STRATUM_ID.worker. Replace the placeholder with your actual account stratum ID and use a distinct worker suffix, such as l9-01 or l11-01. Password: leave blank, or enter a single English character such as x if the interface requires one, following the Hash-Hut setup FAQ.

Use the Scrypt port 9999 for these machines. Select a reachable regional endpoint, then evaluate accepted shares and connection stability from your location. Physical proximity alone does not establish the best route. If you configure backup slots, confirm each endpoint and worker separately; multiple addresses at one operator do not provide operator-level redundancy.

3. Save, monitor and verify

Save the configuration and allow time for the worker to appear. Check both the miner and pool dashboards: the pool should show your worker, accepted work should increase, and rejects should remain low. Short sampling windows can make pool hashrate appear uneven, so compare a longer average before concluding that the hardware is underperforming.

If the worker stays offline, check the account stratum ID, endpoint spelling, port and outbound network access first. If the miner works locally but the pool reports no accepted work, inspect its connection log. Avoid changing clock or voltage settings while diagnosing a basic connection problem; isolate one variable at a time.

Understand fees and payouts before comparing earnings

The Hash-Hut grade system starts with a published 2.9% base fee and advertises reductions down to 0.4% at the highest qualifying grade. That minimum is not the standard fee for every miner. Eligibility depends on the grade rules and qualifying activity.

The grade page is not fully consistent about whether partner-pool charges are included or added. Confirm the total effective fee for your selected route in the dashboard or with Hash-Hut before budgeting. A lower headline fee is useful only when compared on the same basis: accepted work, reward method, payout conditions and all applicable deductions.

The coin pages currently list minimum payouts of 0.01 LTC and 5 DOGE. A positive balance below the applicable threshold does not necessarily mean a payout is missing. Check wallet configuration, threshold and payout status together. Reward accounting also varies by route; do not assume every coin uses one uniform payout method.

For a useful trial, record starting balances, accepted hashrate, rejects, measured electricity use and the actual fees charged. Compare several days under similar operating conditions. Convert all credited coins consistently when estimating revenue, subtract electricity and overhead, and separate unpaid balances from funds already received. Merged mining expands the reward mix; it does not guarantee a profit or a fixed payback period.

자주 묻는 질문

Can I connect an Antminer L9 or L11 to Hash-Hut?

Hash-Hut mining pool publishes Scrypt connection instructions suitable for these miner families. Use the account stratum ID and current Scrypt endpoint, then verify accepted work after saving.

Do I need a second mining connection for DOGE?

DOGE is supported through merged mining on compatible routes. A separate DOGE mining connection is not required for that workflow, but you still need to configure the DOGE payout wallet.

Does every customer receive the 0.4% fee?

No. It is an advertised qualifying grade minimum. Check your actual grade and the total charge for the selected mining route before estimating net revenue.

What should I verify before moving all my miners?

Start with one worker. Confirm accepted work, wallet settings, the selected route, effective fees and a successful payout before deciding whether to expand.

Settings and public terms checked October 30, 2026. Recheck the linked Hash-Hut pages before deployment. Hardware power figures are typical specifications; actual consumption and mining results vary.